Micro Drill Press Model MD70
The MD70 series micro drill press has been discontinued and is no longer available as of January 1st, 2016. We will continue to service our current MD70 customers with a complete line of repair and replacement parts including but not limited to motors, belts, brushes, etc. The MD70 series has been replaced by the Model 704 line of micro drill presses. If you are interested in purchasing a micro drill press please check out our model 704.
Standard Features
- Single Speed Motor
- Three Step Pulley System for Spindle Speeds:
- 9,500rpm, 17,000rpm, 30,000rpm
- Smooth Rack and Pinion Feed
- Drills Small Holes ( 0.002″ to 5/32″ )
- Can Drill to the Center of a 15-3/4″ Work Piece
- Spindle Run Out at Mounting Taper is Within 0.0002″
- Dynamically Balanced Spindles, Pulleys, and Motors for Smoothness in Operation
- Clear Plastic Safety Cover for Viewing Belt & Pulley Position
- Maximum Distance From Chuck Jaws to Work Table is 5″
- J0 taper (J1 if 0-1/4″ chuck is installed)*
* – 0-1/4″ chuck no longer available on current models
Options
- MD70-A-1 – Yukiwa 0-5/32″ Key Type Chuck with key
- MD70-A – Jacobs 0-5/32″ Key Type Chuck with Key
- MD70-C1 – Albrecht 0-1/8″ Keyless Chuck (Hollow Chuck available)
- MD70-C2 – Albrecht 0-1/16″ Keyless Chuck (Hollow Chuck available)
- MD70-C3 – Yukiwa 0-1/8″ Keyless Chuck
- MD151-7 – Travel Dial Indicator
- Hollow Spindles for Special Applications
- DT24A – Extended Columns – up to 6″ longer
- MD70-T – Precision X-Y Cross Slide Table
- MD70-V – Precision 3″ Vise
We Can Help
Contact Cameron Micro
Cameron Micro Drill Presses
Div. of Treat Enterprises
19401 Rawhide Road
Sonora, Ca 95370
1 (800) 369-7769
(209) 532-7201
(209) 532-1211 FAX
Email: sales@cameronmicrodrillpress.com
Our Office Hours are:
8:00am to 4:30pm Pacific Time – Monday through Friday
We are closed weekends and the following Holidays:
- New Years Day
- Memorial Day
- Independence Day
- Thanksgiving Day
- Christmas Day
Standard Features
- Single Speed Motor
- Three Step Pulley System for Spindle Speeds:
- 9,500rpm, 17,000rpm, 30,000rpm
- Smooth Rack and Pinion Feed
- Drills Small Holes ( 0.002″ to 5/32″ )
- Can Drill to the Center of a 15-3/4″ Work Piece
- Spindle Run Out at Mounting Taper is Within 0.0002″
- Dynamically Balanced Spindles, Pulleys, and Motors for Smoothness in Operation
- Clear Plastic Safety Cover for Viewing Belt & Pulley Position
- Maximum Distance From Chuck Jaws to Work Table is 5″
- J0 taper (J1 if 0-1/4″ chuck is installed)*
* – 0-1/4″ chuck no longer available on current models
The MD70 series micro drill press has been discontinued and is no longer available as of January 1st, 2016. We will continue to service our current MD70 customers with a complete line of repair and replacement parts including but not limited to motors, belts, brushes, etc. The MD70 series has been replaced by the Model 704 line of micro drill presses. If you are interested in purchasing a micro drill press please check out our model 704.